![]() Enter the default User Code (1-2-3-4), then press the Lock symbol. Touch the random digits that appear (this is a security feature that ensures fingerprints are spread around the entire screen). The latch bolt will extend to lock.Īctivate the screen. Add User Code: Press the program button the number of times that matches the code. If unsuccessful, make sure the door is unlocked and that you are using a fresh set of batteries. How do i reset my kwikset door lock code. If batteries are low, you will hear 10 beeps. While the door is OPEN and UNLOCKED, activate the screen.Įnter the following code to teach the lock the orientation of the door: To activate the screen, touch screen with palm or back of hand until digits illuminate. How to set a locking and unlocking direction? Repeat from step 1.How to set locking and unlocking direction on my 275 Contemporary Deadbolt? Hold the 9-Volt in place while entering your user code to unlock the door. The edge of the key touches the indent in the cylinder face. When lock has enough power you will hear 3 short beeps. ![]() ![]() Insert the new key you wish to use with the lock. You may feel the tool click inside the lock. If you hear three beeps and the keypad flashes red, it was unsuccessful. Insert the SmartKey tool fully and firmly into the SmartKey hole. You will hear one long beep and the keypad will flash green if successful. ![]() You will hear one short beep and the keypad will flash green.Ĩ. You will hear one short beep and they keypad will flash green.ģ. I got the Kwikset - 955 SmartCode Electronic Pembroke Lever to replace a previous smart lock that used 8 batteries, that drained quickly and was no longer economical. Some models have a plastic pin on the latch handle’s shaft you must remove using a small pair of needle-nose pliers. This review was collected as part of a promotion. Removing the latch handle is done in several ways on Kwikset deadbolt locksets. If you have enabled a programming code, enter your programming code, then press Kwikset. Remove the thumb latch handle on the inside of your Kwikset deadbolt lockset. If you hear three beeps and the keypad flashes red. You will hear one long beep and the keypad will flash green if successful. Going key-free has never been easier with hands-free Auto-Unlock, simple keypad access, Apple Watch compatibility and the option for a back-up key. You will hear one short beep and the keypad will flash green.ĥ. In this video I show you how simple and easy it is to remover the main unit of the Kwikset door lock. You will hear one short beep and the keypad will flash green. If you have enabled a programming code, enter you programming code, then press Kwikset. How do I delete a lock using the Kwikset App Click here to view instructions. If you have not enabled a programming code, press and release the program button. Make sure the hole in the door frame is drilled at least 1 (25 mm) deep. The hole in the door frame for the latch bolt is not drilled deep enough. B The lock beeps, the keypad flashes red, and the door cannot lock. Enter the default User Code (1-2-3-4), then press the Lock symbol. 2 A The lock jams and the turnpiece does not rotate smoothly. If you hear three beeps and the keypad flashes red, it was unsuccessful. Touch the random digits that appear (this is a security feature that ensures fingerprints are spread around the entire screen). B C C 90 90 90 Test Procedure If key does NOT remove, you have successfully rekeyed your lock. Remove the two screws located on the interior side of the door. Make sure new key (B) is FULLY inserted into lock. For example you are unable to program a user code 1-2-3-4-5 as well as a user code 1-2-3-4-6.Ħ) You will hear one long beep and the keypad will flash green if successful. Security on the outside, convenience on the inside. WARNING: For security reasons, the first 4 digits of each user code must be unique. How to re-key Kwikset Smart Lock without key.Smartkey Reset Cradle Tool Link: https:/. You will hear one short beep and the keypad will flash green once.Ĥ) Enter a user code. Heres what to do when youve lost the original Kwikset Smart Lock key. Press and release the program button using the SmartKey tool or a paper clip. If no digit is pressed for 10 seconds, the system will time out and you will need to restart the procedure.ġ) Make sure the door is open. How do I add/delete a user code on my SmartCode 955?
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |